WeCreativez WhatsApp Support
Krrass customer support team is here to answer your questions. Ask us anything!
Hi, how can I help?

The usage and precautions of the ironworker machine

The usage and precautions of the ironworker machine

Ironworker machine in the industrial cutting is very widely used, cutting precision, simple and convenient. But do you know how to operate the ironworker machine sprun? In fact, there is some preparation that is essential before the ironworker machine work. Next, let the small editor to introduce to you.

Guide to how to use the ironworker machine

  1. Hydraulic ironworker machine test when the operation step micrometer fastened to the slider, so that the micrometer above the head on the angle dispensary inspection surface. As the slider moves down, check on the two vertical biases.
  2. The reading difference on the millennium meter is the vertical error travel length of 25 to 50mm0.04 to 0.08;
  3. When the slider moves down, test on the two vertical biases. The reading difference on the millennium scale is the error of parallelity, the travel length of the trip is 25mm s 25mm to 50mm and 0mm to fasten the chidofer on the outer end of the upper tool frame, so that the chiameter measures the head of the head;
  4. Vertical support surface that fits with the lower blade, check the reading difference on the millennium table when the tool holder moves down, the error shear thickness of parallelity is 10mm at 100mm travel length, and the cut thickness is 10mm at 100mm travel On the length; the hole that tightens the punch on the punch gripper, the parallelity of this middle line to the slider movement is 0.040.060.08; the vertical support face that fits the lower blade; the parallelity of the movement of the upper blade; 0. 05 to 0.160.05 to 0.24 Note: When the upper blade moves down, the distance between the two verticals that fit the upper and lower blades;
  5. On the vertical support surface that fits the upper blade; check when the upper tool holder moves down. The reading difference on the micrometer is the difference between the error shear thickness of the parallelity of 10mm at 100mm, and the trip length is: cut thickness of 10mm in the 100mm travel length: the ironworker machine uses a stopper to check the gap between the two ends of the blade;
  6. The difference is the error of parallelity. Hydraulic ironworker machine working principle of the ironworker machine, the upper blade fixed on the knife frame, the lower blade fixed to the bottom bed surface, the bed surface is installed with a tonic ball, in order to facilitate the plate feed into the movement, the rear bezel is used for plate positioning, the position is adjusted by the adjuster pin. The hydraulic pressure cylinder is used to press the plate material to prevent the plate from flipping during shearing. Sheds are safety devices to prevent work-related accidents.

(1) Adjust the front bezel to the rear bezel tight down the knife, and then the model tight back to the rear bezel, the front bezel tight lyson and fixed. Release the rear bezel, remove the template, install the plate material, cut.

(2) After adjustment bezel will be the model to level the next knife, and then the rear bezel tight lysing and fixed, remove the model, and then installthed the plate material for cutting.

(3) Adjust the angle bezel first put the model on the counter alignment under the knife, adjust the angle bezel and fixed, and then adjust the bezel according to the model adjustment bezel, cutting process at the same time use the angle bezel and the rear bezel to position.

Precautions before operation of the ironworker machine

1) The lubrication of each transmission site should be sufficient, each lubrication point refueling 2-3 times per shift;

2) ironworker machine molds should be intact without cracking, fastening and firmly;

3) The gap between the punch and the mold hole wall should be uniform, in line with the requirements of the punch, the punch configuration should be slightly more than the mold hole plane;

4) Equipment electrical insulation, well grounded hydraulic ironworker machine test operation step micrometer fastened on the slider, so that the micrometer to measure the head of the head on the angle gauge inspection surface. As the slider moves down, check on the two vertical biases. The reading difference on the centidon meter is the vertical error travel length of 25 to 50mm0.04 to 0.08;

The reading difference on the millennium meter is the error of parallelity, the travel length of the stroke is 25mm to 25mm to 0mm tightening the chidimeter on the outer end of the upper tool holder, so that the chidimeter measures the head of the head; and the vertical fit with the lower blade Support surface, when the tool holder moves down, check the reading difference on the millennium table, is the parallelity of the error shear thickness of 10mm in the 100mm travel length, the shear thickness of 10mm in the 100mm travel length;

The hole that tightens the punch on the punch gripper, the parallelity of this middle line to the slider movement is 0.040.060.08; the vertical support face that fits with the lower blade; the parallelity of the movement to the upper blade; 0.05 to 0.160.05 to 0.24 Note: When the upper blade moves down, the distance between the two verticals that fit with the upper and lower blades;

Place the chirity on the outside of the table so that the chidness measures the top of the head, on the vertical support surface that fits the upper blade, and when the upper tool holder moves down. The difference in readings on the micrometer is the error shear thickness of the parallelity of 10mm at 100mm, the trip length is: shear thickness and 10mm in the 100mm travel length: the ironworker machine with a stopper to check the gap between the two ends of the blade; and its small difference is the parallelity error.

 

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top